Conveyor Belts – Anis Trend

Sliding Belt Conveyors

ciril — Tue, 07 May 2019 10:04:05 +0000

Lightweight, flat, sliding rubber conveyors (the rubber is stretched during movement and by a tensioning cylinder), supported either by small cylinders or sheet metal.

Sliding belt conveyors are of heavy-duty welded construction and can be manufactured up to 1.9 metres wide. High-quality bearings and drive drums are incorporated for long operating life. Friction conveyors can be fitted with reinforced rubber belting, with or without rubber flights. Sensors can be fitted to monitor belt slip. All sliding conveyors can be fitted with vertical speed drives.

Main features:

Useful widths from 0.3 to 1.9 m
Supported on housing flange bearings
Acceleration belts for automated sorting systems
Articulated belt conveyors, sorting belts, reversing and movement belts possible
RAL-paint according to customer’s wishes

Main Features:

Stable frame construction

With a C-crossbeam profile in the substructure, we can adapt to a range of situations and requirements, which makes it easy to assemble and disassemble all components on the conveyor belt. The conveyor frame is constructed as a modular design, for easy adjustment.

Lateral belt seal in screwed version

The sealing reduces the degree of contamination below the belt and prevents material from getting under the belt and causing misalignment. Due to the bolt design, the rubber strip can be fitted and removed as quickly as possible.

Deflection drum

The deflector drums are equipped with clamping sleeves and continuous shafts, so that the drums can be replaced easily and separately if necessary.
Long tensioning paths guarantee an optimum adjustment of the belt tension.

Self-cleaning devices

Conveyors have optionally self-cleaning decks; self-cleaning carry runs and self-cleaning tail pulleys. These features greatly reduce or eliminate material from being caught under the belt.

The post Sliding Belt Conveyors appeared first on Anis Trend.

Steel-plate Conveyors

ciril — Tue, 07 May 2019 10:03:51 +0000

Robust steel-plate conveyors are mostly used for abrasive, hot or sharp-edged conveyor materials. The steel-plate conveyors can be adjusted precisely to the customer’s needs.

The steel-plate conveyor belt consists of specially designed steel louvers mounted on roller chains. The rollers run on wear-resistant strips. The frame is fitted with easily removable side and bottom sheet work.

Main Features:

Useful widths of 1.000 to 2.000 mm
Above / below belt covers on customer’s needs
By request the plate material can be galvanized, coated steel, plastic, aluminium
Optional: central lubrication units, sensor-controlled overload cut-off, electrically driven cleaning brushes

The post Steel-plate Conveyors appeared first on Anis Trend.

Chain Belt Conveyors

ciril — Tue, 07 May 2019 10:03:37 +0000

Due to their stable and heavy-duty design, chain belt conveyors are preferred in the recycling industry. The high stability coincides with a remarkable flexibility with subsequent expansion or conversion options according to the respective requirements.

Chain belt conveyors can be fitted with rubber. All chain belt conveyors have a heavy-duty welded modular frame construction, with high vertical side pieces, complete with high-quality bearings and gearboxes. All chain belt conveyors can be fitted with variable speed controls.

Main features:

Useful widths of 800 to 2.000 mm.
By default, with chain pitch 100 mm, for medium load 125 mm and for heavy duty load 200 mm.
Screwed-on wear rails on solid cross-beams.
Assembly even in difficult spatial conditions.
Height of side walls: 300-750 mm (horizontal part) and 300-1.250 mm (ascending part).

ANIS manufacture 3 series of chain belt conveyor belts:

LIGHT LOAD: with a chain pitch of 100mm for light load and 4kW motor power

MEDIUM LOAD: with a chain pitch of 125mm for light load and 4kW motor power

HEAVY DUTY LOAD: with a chain pitch of 200 mm and 4 – 7,5 kW motor power for industrial waste, large quantities of waste paper and MSW

Main features:

Machine Frame

The conveyor frame consists of a heavy, solid steel structure. The vertically mounted side pieces avoid material jams and build-ups.
Additional guides below the conveyor belt absorb heavy loads or jolts (horizontal part).

Modular design:

The frame structure is designed as a modular construction, so that extensions can be realised in a quick and cost-efficient manner.
A lot of maintenance openings in the heavy, solid sheet steel edging design.

Swan’s neck

The additional, conical upper side at the top end of the conveyor belt with a “swan’s neck” prevents material from falling over the sides during transfer to the press hopper.

The gradient is usually 30° with installation either in a recessed pit or above the floor and a conveyor outlet gradient of up to 15° (swan’s neck). Inclined conveyor belt is reinforced with height adjustable H-supports.

The bottom cord cover on the complete conveyor length is galvanized.

The quick and easy disassembly of the components allows access to the chains and cross-beams in all positions.

Chain Guide

Large sprockets assure soft and uniform speed. The chain routers can be fitted with polyurethane linings (option). This significantly reduces the noise generated by the entry of the chain, even at high conveyor belt speeds.

Chain / Belt

The torsion-resistant belt support profiles accommodate the belt.
The material driver and C-crossbeams are galvanised. These ensure a long life even under difficult conditions. Optionally, the conveyor can be fitted with special oil- and grease-resistant rubber belt.

The chain bolts and rollers are made of hardened steel. Extremely stable link plates make it possible to operate with heavy loads.

Lubrication system

To make possible environmentally friendly, cost-effective operation, the automatic drip lubrication system is fitted with an automatically controlled solenoid valve.

A standard drip oiler lubricates the chain with brushes mounted directly on the chains. Lubrication should only be carried out when the chain is moving.

Emergency stop devices

The chain conveyors are fitted with clearly visible control devices (emergency stop and other controls where appropriate) to perform all the necessary tasks for safe operation.
Start/Stop switches and a rope-pull emergency STOP switch on the rising conveyor stand.
An additional tripwire arranged like “goalposts” over the conveyor is fitted with suspended rope-pull emergency STOP cords positioned at regular intervals along the conveyor length.

PERSON PROTECTION SYSTEM IN DANGEROUS ZONE OF THE CONVEYOR

Optionally, for personnel safety the conveyors are mounted with a safeguard of an automatic RFID personnel detection system in dangerous zone of the conveyor.

Control system

Speed regulation Variable Frequency Drive
Additional controls (near operator working areas)
Mobile controls (optional on request)
Special programming for baler-conveyor operation (feeding level control, high-low density materials, manual control, hopper jamming)